Skip to main content
iRubric: SMAW E-6011 1/8" Bead Pad rubric

iRubric: SMAW E-6011 1/8" Bead Pad rubric

find rubric

edit   print   share   Copy to my rubrics   Bookmark   test run   assess...   delete   Do more...
SMAW E-6011 1/8" Bead Pad 
SMAW E-6010 1/8" pad-o-weld
Students will use SMAW welding techniques to weld a bead pad with 1/8" E-6011 welding rods.
Rubric Code: LX92WC8
By rmyatt
Ready to use
Public Rubric
Subject: Vocational  
Type: Project  
Grade Levels: 9-12

Powered by iRubric Welding Joints
  Advanced

10 pts

Proficient

8 pts

Basic

6 pts

Below Basic

4 pts

Weld width and height:
100 pts

Uniform width and thickness throughout the entire length of each weld.
Advanced

Bead is uniform width all along the length of each weld. Has a smooth appearance
Proficient

Bead maintains width and length. Shows some small blemishes along the weld
Basic

Not a uniform thickness through out the weld. Thickness goes to extremes
Below Basic

Weld is cut off in places, not uniform along the weld. Shows bare spots
Appearance
100 pts

Smooth with uniform dense ripples, doesn’t show the bead traveling to fast or slow
Advanced

Weld shows a constant speed and uniformity the entire length
Proficient

Weld shows a constant speed with some blemishes that are minimal
Basic

Weld shows definite areas of speeding up and slowing down. Ripples tend to be coarse
Below Basic

Weld has been done to fast or to slow. Weld is not complete
Face of bead:
100 pts

Convex, free of voids and high spots, shows uniformity throughout the bead
Advanced

Has a nice rounded look. Is not overly high, or low. Bead covers a wide area of each weld.
Proficient

Bead is well rounded, mostly uniform over the length of the weld. Shows some high spots and low spots
Basic

Bead shows many high and low areas. Total lack of uniformity throughout the weld
Below Basic

Weld does not blend into one single bead.
Edge of bead
100 pts

Good fusion, no overlapping or undercutting
Advanced

Sides and edges are smooth blending into each weld. Undercutting is kept to a minimum, Weld does not float on surface
Proficient

Moderately smooth blending. Undercutting and float are present. Stength of the weld is still strong
Basic

Float and undercut are very apartent. Weld lacks strength and flow
Below Basic

Metal is burned through. Weld has no connection to metal,
Beginning and ending full size
100 pts

Crater well filled
Advanced

End of each weld is complete, the line doesn't taper off
Proficient

Weld ending is full but shows some tapering and a crater is present
Basic

Crater distinctly present at the end of the bead.
Below Basic

Metal is burned through at the end
Bead placement
100 pts

Beads slightly overlap, leaving no gap in between beads
Advanced

Each bead is placed immediately next to the previous, with slight overlap
Proficient

Each bead is placed immediately next to the previous, no overlap
Basic

Small gap is present in between beads
Below Basic

Large gap exists in between beads
Pad completion
100 pts

Bead pad is full of uniform beads from start to finish
Advanced

Bead pad is full of uniform beads from start to finish
Proficient

Bead pad is full; some spaces exist but no spaces large enough for another bead
Basic

Bead pad is mostly full, but has room for more beads
Below Basic

Bead pad is incomplete, several more beads can be placed within the pad surface
Bead cleanliness
100 pts

Each bead has been chipped free of slag, and wire brush has been used to clean off each bead
Advanced

Each bead has been chipped free of slag, and wire brush has been used to clean off each bead
Proficient

Beads have been chipped and brushed, but some slag inclusion exists
Basic

Beads have been chipped, but do not show to have been wire brushed
Below Basic

Beads have not been cleaned off
Base metal dimension
100 pts

The base metal for the bead pad has been cut to proper dimensions
Advanced

Base metal has been cut to proper dimensions
Proficient

Base metal has been cut to within 1/4" of correct measurement
Basic

Base metal cut within 1/2" of correct measurement
Below Basic

Bead pad has been cut over 1/2" of correct measurement
Correct welding rod
100 pts

Beads welded with 1/8" E-6011 rods
Advanced

Beads welded with 1/8" E-6011 rods
Proficient
Basic
Below Basic

Beads welded with wrong size rods or rod type




Subjects:


Discuss this rubric




Do more with this rubric:
Preview

Preview

Preview this rubric.
Edit

Edit

Modify this rubric.
Copy

Copy

Make a copy of this rubric and begin editing the copy.

Print

Print

Show a printable version of this rubric.
Categorize

Categorize

Add this rubric to multiple categories.
Bookmark

Bookmark

Bookmark this rubric for future reference.
Assess
Test run

Test run

Test this rubric or perform an ad-hoc assessment.
Grade

Grade

Build a gradebook to assess students.
Collaborate

Collaborate

Apply this rubric to any object and invite others to assess.
Share
Publish

Publish

Link, embed, and showcase your rubrics on your website.
Email

Email

Email this rubric to a friend.
Discuss

Discuss

Discuss this rubric with other members.
 

Do more with rubrics than ever imagined possible.

Only with iRubrictm.


Copyright © 2024 Reazon Systems, Inc.  All rights reserved.
n98